Timing viewing of FAG bearings is especially important

Source: Bearing network time: 2014-08-22

/*250*250 was created on 2017/12/25*/ var cpro_id = 'u3171089';

FAG bearings remind you to regularly repair mechanical equipment; it is very important to ensure the production. As a fine fitting of mechanical equipment; the timing of the bearing is particularly important. Today we will analyze the key steps of FAG bearing timing inspection. Smooth and clean is very important. Before you look at it, you need to sanitize the machine; then remove the parts around the bearing. The oil seal is a very weak part; therefore, be careful to disassemble it; do not apply excessive force; then carefully check the oil seal and The parts around it; if they have exhibited poor performance; they must be replaced; poor oil seals will cause damage to the bearings and severe equipment stops.
FAG bearings check the smoothing agent with a little bit of smoothing agent between the two fingers; if there are contaminants; can feel it; or apply a thin layer of smoothing agent on the back of the hand; then seal the light to see.
Replace the smoothing agent oil smooth FAG bearing after the old oil is drained; if possible; refill the fresh oil and let the machine rotate at low speed for a few minutes. Try to get the oil to collect the residual contaminants; then vent the Engine oil; the oil is best filtered before use. The smoother FAG bearing used in the replacement of grease should prevent the joint with cotton to any part of the bearing; because of these residual fibers Can be wedged between the rolling elements and form damage; especially the use of small bearings need to pay attention to this problem.
Cover the exposed bearing to check the bearing; do not expose the bearing to contaminants or moisture. If the operation is stopped, the machine should be covered with oil-paper plastic sheet or similar information. If you do not have to disassemble, you can perform the inspection. Remove the unshielded bearing under the scene; remove it with a white spirit by applying a brush; then dry it with a lint-free cloth or blow it with compressed air (focus on not letting the bearing assembly start to rotate) Use a small mirror and a probe used by a similar dentist to view the track surface of the bearing, the holder and the beads. If the bearing is not damaged, it should be based on the smooth explanation provided by the original machine or from pages 204 to 247 of this book. The page's claim is fulfilled and smooth. It is not necessary to remove the bearing with the sealing cover or dustproof, only scrub the external appearance. If the bearing is damaged, it needs to be replaced. The replacement of the bearing during the timed protection period is far better than the selection due to the bearing damage. Itâ€™s more economical to stop losing.

Recommend to friends comments close window

Bearing related knowledge

The rear code of NSK bearing clarifies the characteristics of angular touch ball bearing and the use of Pump bearing seal is not resistant to wear, high temperature treatment program grinder static pressure imported bearing repair method bearing type system science angle touch ball bearing

This article links to http://
Please indicate China Bearing Network http://

Previous:Unpacking the door of NSK imported vibrating screen bearing Next:NSK axis and shaft cooperation test

Photovoltaic System

Solar cells use sunlight to generate electricity. As long as the sun shines on the battery, it will continue to generate electricity. It is a clean energy with the advantages of safety, reliability, no noise and no consumption of raw materials. It has the advantages of great convenience for residents in remote areas. So what is the working principle of solar energy? Today we'll explore it. Solar cell is a device that directly converts light into electric energy through photochemical effect. When sunlight shines on the semiconductor pn junction, a new hole (electron pair) is formed. Under the action of the electric field, the hole flows from the N region to the p region, and the electron flows from the p region to the N region. After the circuit is connected, a current is formed to convert light energy into electric energy.Solar panel, also known as solar cell module, is a kind of photoelectric semiconductor sheet that uses sunlight to directly generate electricity. It is an assembly composed of several solar cells assembled on a plate in a certain way. It is the core part of the solar power generation system.The earth, the green home for human survival.
With the development of human civilization, it has gradually become a victim of economic growth. Clean energy is imminent.
The sun concentrates 99.87 percent of the mass of the solar system, and one twenty-two percent of the energy radiates to the earth, becoming the main source of photosynthetic heat on the earth. Solar energy is one of the cleanest, most lasting and most magical energy of all.

Photovoltaic System,Solar panels,Solar controller,High power inverter,Household solar panel,Monocrystalline silicon solar panel

Rugao Yaou Import & Export Trade Co., Ltd , https://www.ntyaoumachinery.com