1. Ways to Create Space - Open the Rescue Channel Completely
Dashboard rotation (old car)
Dashboard rotation (new car)
This is to make the dashboard rotate forward to keep away from the wounded.
action | Considerations | equipment |
After dismantling the front door, place the hammer between the base of the B- pillar and the middle part of the A- pillar | - Expose all vehicle interiors before placing the hammer - Use a hammer stand to make the base stronger | Jack, hard protection |
Make an incision at about 45 degrees on the A- pillar base | - Expose vehicle interior before cutting - Make sure the cut removes as much force as possible | Cutter, hard protection |
A half cut portion | - Expose vehicle interior before cutting - Make sure to use respirators (dust masks) during cutting of glass | Cutter, hard protection |
Extend the hammer to turn the dashboard | - Expose all vehicle interiors before placing the hammer - After the incision is opened, insert the wedge to ensure that the dashboard does not turn back when the hammer slides | Jack, wedge, hard protection |
Remove the hammer to resume full access to the vehicle and cover the sharp edge with a sharp-edged protective cover | - Once the wedge is in place, the hammer can be removed | Wedge, sharp edge protection cover |
2. Ways to Create Space - Open the Rescue Channel Completely
Dashboard rotation (old car)
Dashboard rotation (new car)
This is to move the dashboard up and forward to keep away from the wounded.
action | Considerations | equipment |
After removing the outer wing (fender), a wedge-shaped groove is formed between the partition and the MacPherson suspension in the inner wing (fender) | - Ensure that the dovetail groove is between the bulkhead and the McPherson suspension - Ensure that the structure needs to be cut - Ensure that the wedge-shaped grooves produce loose material | Cutting pliers, with protection |
Two open cuts in the base parallel to the A-pillar of the window, the first cutout as low as possible, as high as the second incision | - Expose vehicle interior before cutting - Make sure these cuts remove as much force as possible - If the cutting pliers start turning towards the passenger compartment, stop moving and reposition | Cutter, hard protection |
Fixed to the stent between two notches and folded outwardly for the relocation of the footwell | - Expose vehicle interior before cutting - If this is difficult, you need to make a more effective incision | Cutter, hard protection |
Cut off the upper part of the A- pillar (high-rise) | - Expose vehicle interior before cutting - Make sure to use respirators (dust masks) during cutting of glass | Cutter, hard protection |
Use a spreader that repositions the footwell to move the dashboard and cover the sharp edge with a sharp-edged protective cover | - Place the dilator in place so as not to affect access to the vehicle | Dilator, hard protection, sharp edge protection cover |
3 , the method of creating space - fully open the rescue channel
Dashboard movement replacement options
This is to move the dashboard up and forward to keep away from the wounded
action | Considerations | equipment |
Exposing horizontal instrument panel reinforcement | - May not reveal horizontal instrument panel reinforcement | Exposed tools |
Expand from sill to dashboard reinforcement and move dashboard vertically | - Ensure that the injured are fully protected | Dilator, hard protection |
4. Ways to Create Space - Open the Rescue Channel Completely
Cross hammer (horizontal / vertical)
This is to relocate the body structure by entering the vehicle to make room inside
action | Considerations | equipment |
Determine relative strength points and prevent hammers | - Expose all vehicle interiors before placing the hammer - Ensure that the sturdy base and the selected hammer point do not cause the slider to slide | Jack, hard protection |
Unfold the ram and expand the body structure to the desired position | - Expose all vehicle interiors before placing the hammer - Moving the vehicle structure to change its original shape and position will reduce the risk of structural restoration after removing the hammer - Communication is critical during hammering - When vertical hammering, keep in mind that the roof structure is relatively weak, so care must be taken to prevent piercing through the roof structure with side tool holders | Jack, hard protection |
! Remember - the techniques described in this article can be adjusted and used for vehicles in any orientation (that is to say for vehicles with wheels, body or roof landing), but the emphasis is always on safety.
5. Ways to Create Space - Open the Rescue Channel Completely
Remove B column
This change aims to completely remove the vehicle B- pillar.
action | Considerations | equipment |
Cut off the B column at a lower position | - Expose vehicle interior before cutting - First cut at a low point. If you cut off the B- pillar at a height , this will increase the risk of moving the top of the B- pillar to the passenger compartment while increasing the shear at the lower part. - Shear at the same height as the wounded person's seat or slightly below the wounded person's position. The B- pillar at this position is more narrow, without cutting too much | Cutter, hard protection |
Shear above the B-pillar and wrapped around a sharp edge with sharp corners blanket of | - Expose vehicle interior before cutting - Control the B- pillar during the cutting process because it becomes loose at the moment | Cutter, hard protection, sharp edge protection cover |
Move the B column to the debris heap | - Be careful to move because B- pillars may contain pre-tensioned seat belts | no |
6. Ways to Create Space - Open the Rescue Channel Completely
Remove the pedal
This is to create space at the feet of the driver
action | Considerations | equipment |
Cut off the pedal | - Communicate with medical staff to ensure that the pedal can be safely removed (with the help of medical staff, the injured person's lower limbs can be moved to enter the vehicle) - To remove pedals in a controlled manner and maintain communication with health care personnel because they are extremely close to the injured | Pedal nippers / micro-cutters, hard protection |
Cover sharp edges with sharp-edged protective covers | - Carefully cover sharp edges | Sharp edge protection cover |
7. Ways to Create Space - Open the Rescue Channel Completely
Reposition the pedal (pull sideways)
This is to create space at the feet of the driver.
action | Considerations | equipment |
Tie the pedals with a rope / belt and wind the top of the door frame closing the door | - Communicate with medical staff to ensure that the pedal can be safely removed (with the help of medical staff, the injured person's lower limbs can be moved to enter the vehicle) - To remove pedals in a controlled manner and maintain communication with health care personnel because they are extremely close to the injured | Rope / belt |
Slowly open the door and reposition the pedal | - Reposition pedals in a controlled manner and maintain communication with health care workers | Rope / belt |
8. Ways to Create Space - Open the Rescue Channel Completely
Forward roof baffle
This is to reposition the roof.
action | Considerations | equipment |
| Solar LED Holiday Light Solar Led Holiday Light,Solar Garland String Light,Led String Light For Christmas,Solar Garland String Fairy Lights Shenzhen You&My Electronic Technology Co., Ltd , https://www.youmysolarlight.com |