First, the quality of steel doors and windows profiles
The appearance of the profile should be observed. The color should be blue-white, not white, which is usually considered by people. Pay attention to whether the color of the frame and the fan profile of the door and window is consistent, whether the appearance is uniform and whether the cavity distribution is reasonable. In the formulation of steel door and window profiles, calcium carbonate is usually added as the filler material, and some manufacturers reduce the cost. If the amount is too much, it becomes a calcified plastic. The surface of doors and windows made of this plastic lacks luster and is slightly rough. Hard and brittle, it looks like a rough feeling like stones, normal steel doors and windows, the surface is usually shiny, very tough.
Second, the gap between doors and windows and seal
Look at the tightness of the fit between the various profiles, whether the incision is flush with the fit, the height of the profile overlap, and so on. General steel doors, the main part of consideration is the door frame, the gap between the fan, the door trim and the door edge, the various sections of the shutter connection, seals, etc.; if assembled door panel, but also consider the door Gap; is to open the door but also whether the two doors closed after the light and so on.
Similarly for the use of plastic steel windows, in addition to the assembly of a variety of profile assembly clearance to be considered, the sealing strip is uniform and solid is also very important, the interface gap should not exceed 1mm, which reflects the window sealing performance. Plastic-steel doors usually do the inner door of a building, and the sealing requirements are not so high. Various clearance values ​​are stipulated in national standards, but for customers, the smaller the gap value at various profile connections, the tighter the fit and the more exquisite the assembly process, which reflects the assembly level and the accuracy of the assembly tools.
Third, the welding of steel doors and windows
To see if the weld is flush, whether there are cracks, and whether the internal and external corner seams are clean and beautiful, use a box ruler to measure the diagonal size of the steel doors and windows, the diagonal size difference should be no more than 3mm, diagonal difference The smaller the display process, the finer it will be for installation.
Fourth, hardware and steel doors and windows hardware
The quality of hardware has a certain influence on the life of doors and windows. The hardware used should look thick, and the surface gloss is better, the protective layer is denser, and there is no scratching phenomenon. The most important point is that the opening should be flexible.
Fifth, reinforced steel doors and windows reinforced steel
According to national standards, there are different requirements for the wind pressure resistance of plastic steel doors and windows. The frame of plastic steel doors and windows and the inner cavity of the fan shall be equipped with reinforced steel. According to the height, there are three types of reinforced steel of 1.2mm, 1.5mm and 2.0mm to ensure the The product's ruggedness and longevity. In order to reduce costs, some manufacturers do not install or load reinforced steel that does not meet the requirements. Customers should pay special attention when purchasing products. The usual inspection methods are:
1, the reference weight method estimates, that is, the weight of the nickname windows and doors, equipped with reinforced steel doors and windows weight, otherwise it is light.
2. Use a magnet to place the frame and fan on the door and window. If the magnet is adsorbed, there will be reinforced steel in the profile, and vice versa.
3. Observe the frame of the door and window, whether there are screws fastening the steel on the fan, it can also prove whether there is reinforced steel.
In short, customers should be cautious when choosing products, try to use regular manufacturers' products, and strictly inspect them so as not to be deceived.
Sixth, buy plastic doors and windows matters needing attention
Do not buy cheap steel doors and windows
Pay attention to glass and hardware. The glass should be smooth and dry. The glass and plastic profiles are not in direct contact and there is a sealing bead that closes the gap. The hardware is complete, the position is correct, the installation is firm, and the use is flexible.
The surface of doors and windows should be smooth and flat, and there should be no open welding breakage. The sealing strip should be flat, without curling, no groove removal, and no smell on the strip. When the doors and windows are closed, there is no gap between the fan and the frame.
Four doors and windows are all integrated and screwless.
Sliding doors and windows open and slide freely, soft sound, no dust off.
Special steel linings are embedded in the window frames and fan profiles.
The glass should be flat and securely mounted. The installed glass does not directly contact the profile. Glass glue cannot be used. If it is a double glass flat layer, there should be no dust and moisture in the interlayer.
Switch parts are tightly closed and flexible.
Plastic steel doors and windows are all manufactured on the factory floor using professional equipment and cannot be produced on the construction site.
Door and window acceptance window glass switch shutter glass glass sliding door glass door shutter door
Basin Faucet,Wash Basin Faucet,Face Basin Faucet,Water Tap For Wash Basin
Heshan Janno Kitchen and Bath Technology Co.,Ltd , https://www.janno-ks.com