During the slack season, the submersible pumps should be cared for the necessary maintenance to prolong their service life and ensure normal use during busy hours. First, check the most easily damaged parts. Submersible pump impeller, buckle, bushings, housings, etc. are vulnerable parts. First of all submersible pump should be removed, check the fragile parts are intact. Prohibit the use of damaged and unqualified submersible pump parts II, timely inspection and replacement of lubricants. To ensure the normal lubrication system, you need to regularly check the lubricating oil, then to open the seal chamber and the motor within the hole screw, the sealed chamber and the internal motor oil all released, replace the new oil three, to prevent rust The demolition of the pump shell. Spring before use, should be disassembled pump casing at the top, turn the impeller and then start closing, to prevent rusting parts can not start normally and burn the motor. This maintenance is particularly important for water-filled motor Fourth, to ensure good sealing performance. Agricultural submersible pumps on the sealing requirements are very strict, in the replacement of sealed chamber lubricant, if you find the oil cloudy and moisture content, you must replace or replace the seal box or seal the entire ring to ensure good sealing performance Fifth, the drying Motor: Measure the insulation resistance of the submersible pump windings and the housing with a 500 megaohms meter. If the resistance is less than 0.5 megohms, remove the motor moisture. Drying methods are: external drying method, current drying method and the combination of both at the same time dry. External drying method is the use of external heat source for processing, commonly used measures are: ⑴ hot air: the use of electric heater blower (small submersible pump available hair dryer) hot air blowing to achieve the purpose of drying; ⑵ bulb baking: Closed box, the use of several 200-watt light bulbs for baking. Note that the baking temperature can not be too high, should be controlled below 125 ℃; ⑶ current drying: According to the submersible pump impedance and power supply size of the motor windings in series or in parallel, and then access a variable resistor, adjust the current About 60% of the rated current, power drying six, bearing lubrication must be sure. Inspect the water-filled submersible pump regularly and replace the skeleton oil seal and lithium grease of the upper and lower end cap bearing chamber. To ensure long-term lubrication of the bearing in good working condition Seven, to ensure that the inspection bearings. Before each use need to check the motor part of the upper and lower bearings, if found to wear or clearance is too large, must be promptly replaced with new bearings, is strictly forbidden to make improper use. Check the method is as follows: 1, if the motor is running, resulting in carbolic sound, and the cycle and speed is proportional to, and feel trouble when the rotor is rotated, the bearing raceway is a bit astringent or avulsion phenomenon; 2, Intermittent sizzling sound, turning the rotor by hand when there is an indefinite dead, usually broken ball cage, the inner ring broken ball or broken. In the event of these circumstances, the bearings must be replaced to avoid further damage.
Swage Terminals
The main purpose and scope of application of the shackle: The shackle can be used for the end fittings of the rigging, and is directly connected to the object to be lifted during the lifting operation. Shackles can be used between rigging and end fittings, only for connection. When the rigging is used in conjunction with the beam, the shackle can be used to connect the rigging with the lug plate at the lower part of the beam instead of the lifting ring, which is convenient for installation and disassembly. Shackles are widely used connection tools in lifting operations, and are mainly used for connection parts that are often installed and disassembled in hoisting. D-type shackle is mainly used for single-limb rigging; B-type shackle is mainly used for multi-limb rigging. The company can design and produce other types of stainless steel products according to customer requirements. The company has a number of professional precision casting production lines, CNC machining lines, and machining centers. It also owns advanced spectral analysis quality inspection equipment to ensure material quality. High-pressure pressure test leak detection equipment, air tightness detection equipment, angle test bench, national standard tooth gauge, ring gauge and optical gauge, solid melting furnace and other equipment, technical capabilities. Fangzheng Stainless Steel Rigging sincerely invites friends from all over the world to visit and negotiate with our company, and jointly develop the world rigging, marine hardware accessories, stainless steel pipe valve parts, and auto parts market. This product is made of stainless steel 304, 316.
Swage Terminals,Swage Eye Terminal,Swage Stud Terminal,Swage Fork Terminal
Jiangsu Hongze Stainless Steel Wire Rope Co., Ltd , https://www.hzrope.com