Hydraulic pump failure cause analysis: In the maintenance of hydraulic pump from the following three points to find the cause of the malfunction, and the system to improve: (1) check the boom cylinder leakage situation. The easiest way is to raise the boom to see if there is a clear free fall. If the whereabouts of obvious removal of fuel tank inspection, seals have been worn should be replaced. (2) check the control valve. First clean the safety valve, check whether the spool wear, such as wear and tear should be replaced. If there is still no change after installation of safety valve, and then check the control valve spool wear, the gap limit of use is generally 0.06mm, severe wear and tear should be replaced. (3) measure the pressure of the hydraulic pump. If the pressure is low, then make adjustments, the pressure is still not adjustable, the serious damage to the hydraulic pump. In general, the main reason that the boom can not be lifted is: a. The hydraulic pump is seriously worn. The pump leaks seriously at low speed. When the pump runs at high speed, the pump pressure slightly increases, but due to the pump wear and leakage, the volumetric efficiency drops significantly and it is difficult to reach the rated pressure. Hydraulic pump work for a long time has exacerbated the wear and tear, oil temperature, resulting in wear and tear of hydraulic components and seals aging, damage, loss of sealing ability, hydraulic oil deterioration, and finally lead to failure. b. hydraulic components selection is not reasonable. Boom cylinder specifications for 70/40 non-standard series, the seals are also non-standard parts, high manufacturing costs and seal replacement inconvenience. Boom cylinder bore is small, the system is bound to set high pressure. c. Hydraulic system design is not reasonable. Control valve and full hydraulic steering gear for a single pump in series, safety valve setting pressure points 16MPa, while the hydraulic pump rated working pressure is also 16MPa. Hydraulic pump often at full load or prolonged overload (high pressure) work, and the system has a hydraulic impact, long-term oil does not change, the hydraulic oil contaminated, exacerbating the hydraulic pump wear and tear, resulting in hydraulic pump shell burst (was found Such failure). Improvements and effects: (l) Improve hydraulic system design. After several demonstrations, the final use of advanced priority valve and load sensing hydraulic steering gear form, see Figure 2. The new system can give priority to the distribution of traffic in accordance with the steering requirements, regardless of the size of the load, the steering wheel speed can ensure adequate supply of oil, the remaining part can be fully supplied to the working device circuit, thus eliminating the power supply due to excessive steering oil supply Loss, improve the system efficiency, reducing the working pressure of the hydraulic pump. (2) Optimize the design of boom cylinder and hydraulic pump to reduce the pressure of system work. Through optimization calculation, the boom cylinder adopts standard series 80/4. Hydraulic pump displacement increased from 10ml / r to 14ml / r, the system set pressure of 14MPa, to meet the boom cylinder lifting force and speed requirements. (3) Pay attention to proper use and maintenance of loaders in the process of using, regularly add or replace hydraulic oil, maintain the cleanliness of hydraulic oil, and strengthen routine inspection and maintenance.
Plano-Concave Spherical Lens
Spherical lenses often used for aiming and focusing of monochromatic light source.Plano-Concave Lenses have a negative focal length and is typically used to cause a collimated beam to diverge as in a Galilean type beam expander or Telescope. Because the spherical aberration of thePlano-Concave is negative, it can be used to balance the aberration of other lenses. This lens is widely use in optical display systems, projection optics systems, imaging and laser measureemnt systerms.
We supply kinds of Plano-Convex Spherical Lens,plano-concave Spherical Lens,bi-convex spherical lens,bi-concave spherical lens,Meniscus Spherical Lens,special spherical lens,achromatic spherical lens,ball lens,sphere lens etc.
Specification of our spherical lens as follow:
*Material: BK7,fused silica,MgF2,BaF2,CaF2,ZnSe,ZnS,Ge or other optical crystals
*Dimension Tolerance +0.0 -- -0.1mm
*Center Thickness +/-0.1mm
*Focal Length Tolerance+/-1%
*Surface Quality:60/40
*Surface Figure: lambda/2 at 633nm on plano side
*Clear Aperture >90%
*Chamfer 0.25mm at 45 degree typical
*Coating Optional
Plano-Concave Spherical Lens,Optical Plano-Concave Lens,Double-Concave Lens Kit,Simple Double-Concave Lens Kit
China Star Optics Technology Co.,Ltd. , https://www.opticsrealpoo.com