The electric faucet is deeply loved by people because of its water-saving performance and its ability to reach a constant temperature quickly. The quality of the electric faucet is partly derived from its own material and the excellent quality of the production process, while on the other hand it comes from the installation quality of the electric faucet. The installation steps and processes of the electric faucet directly determine the quality of the installation. The specific installation process and steps are as follows:
1. Install the filter:
The electric faucet must be installed with a filter at the inlet, because there is a small amount of debris in the tap water, and the electric faucet can be used to avoid getting stuck or clogging the shower. If the filter is clogged, the flow will be reduced, the water will be reduced, and the floating magnetic non-operating electric faucet will not be heated. After using for a period of time, remove the filter of the electric faucet for cleaning and use.
2. Check the floating magnetic position:
When installing the electric faucet, the installer must remember to check whether the floating magnet is at the lower end, so that it is in a freely movable state to ensure the normal use of the electric faucet. Because the floating magnet is the water and electricity linkage switch, the water valve is automatically heated and the water is turned off to stop heating. If there is any debris to catch the floating magnet, the electric hot water tap will dry or not heat, and the debris on the floating magnet can be removed. normal work.
3. No mixing valve:
The electric faucet does not need to use the mixing valve, because if the mixing valve is used, there will be cold and hot water mixing and flowing out at the same time. At this time, the flow rate of the hot water will become smaller, causing the water temperature of the electric faucet to be too high and over temperature. There will be a phenomenon of water being cold and hot. The staff should inform the customer who uses the mixing valve to directly boot to the hot water end without mixing cold water, which will make the product last longer and less prone to scaling.
4. Control water flow:
When using the electric faucet, the manufacturer must be equipped with a special shower. Under normal working conditions, the electric faucet can adjust the water flow or increase the water temperature. However, the average user has no habit of controlling the flow of the faucet, so that the water temperature does not reach the predetermined effect.
In short, the installation requirements of electric faucets are relatively professional. It is recommended that people look for professional manufacturers to purchase such products, because large-scale enterprises will be equipped with professional installation teams for on-site installation services, and the installation quality is better than the average. The master is more professional, and the owner is advised not to be cheap.
Concerned about surprises
Label: electric faucet installation steps and processes
Previous: Selection tips for aluminum alloy doors and windows Next: Conditions for floor heating for geothermal
Epoxy Flat Ground And Mortar Floor
Scope of adaptation:
Electrical appliances, electronics, machinery, food, medicine, chemicals, tobacco, beverages, textiles, clothing, furniture, plastic, stationery and other manufacturing plant workshop cement or terrazzo floor.
Performance characteristics:
1, dust, moisture, wear-resistant;
2, easy to clean, fast construction, easy maintenance, low cost;
3, strong adhesion, good flexibility, impact resistance;
4, Epoxy thin coated floor thickness 0.3 ~ 0.5mm;
5,Epoxy mortar flat coating thickness of 1.0 ~ 5.0mm range.
Generally 3 to 5 years
Technical index:
|
project |
index |
|
|
Drying time |
Table dry |
≤4 |
|
action |
≤24 |
|
|
Adhesion (grade) |
≤1 |
|
|
Pencil hardness |
≥2H |
|
|
Impact resistance |
50 passed |
|
|
Flexibility |
1mm passed |
|
|
Wear resistance(750g/500r,weightlessness,g) |
≤0.04 |
|
|
Water resistance |
No change in 48 hours |
|
|
Resistant to 10% sulfuric acid |
56 days no change |
|
|
Resistance to 10% sodium hydroxide |
56 days no change |
|
|
Gas-resistant,120 "Anti-petrol,120". |
56 days no change |
|
|
Anti-lubricant |
56 days no change |
|
Construction Technology
1, the base surface treatment;
2, brushing primer;
3, grant putty or mortar layer;
4, polished, vacuuming;
5, paint color paint;
Epoxy Flat Ground And Mortar Floor
Epoxy Flat Ground And Mortar Floor,Flat Painted Epoxy Floor,Light Grey Epoxy Flat Coating,Grass Green Epoxy Flat Coating
Jiangmen Kasole Building Materials Co., LTD. , https://www.kasole-paint.com