The hammer mill is a machine that uses a high-speed rotating hammer to crush the feed. It has the advantages of wide versatility, low temperature sensitivity to feed, good crushing quality, convenient use and maintenance, and high productivity. However, if the user has insufficient analysis of several key problems affecting the performance of the crusher, the productivity will be low, the power consumption will be large, and the crushing quality cannot be guaranteed. This article describes several key issues to be aware of when using a hammer mill and analyzes it.
Step / Method
Generally, the moisture content of the feed during pulverization does not exceed 15%.
The moisture content of the feed increases, the structural crispness decreases, the feed is not easily crushed, and the productivity and electrical output are reduced. Tests have shown that when corn moisture content increases from 14.3% to 21%, its productivity decreases by 29% and power consumption increases by 12.5%; when barley moisture content increases from 13.8% to 20%, its productivity decreases by 30% and power consumption increases by 12.5%. The moisture content of the feed when pulverized is required to not exceed 15%.
The speed of the hammer is very influential. In a given range, when the stalk feed is crushed, the value is taken low. When smashing the grain feed, the high value is taken.
The hammer speed has a great influence on the productivity and power consumption of the pulverizer. Tests have shown that when the hammer speed is too low, the impact ability is lowered, and the wind power of the suction powder is also small, so the productivity is low and the power consumption is increased. When the speed is high, the pulverizing ability and the powder discharging ability are increased, and the productivity is improved. However, if the speed is too high, the vortex action of the pulverizing chamber is strengthened due to the increase of the blasting action of the rotor, resulting in an increase in no-load power consumption, and at the same time, the material speed is too high, and the chance of discharging the mesh hole is reduced, so the pulverization efficiency is also relatively decreased. In addition, if the hammer speed is too high, the power consumption of the bearing friction and the agitation air will increase sharply, and the energy consumption per unit product will be significantly improved. Therefore, each type of shredder has a suitable speed range. In recent years, the hammer speed of the pulverizer has been improved. Generally, the pulverizer used in the farm is 60_70m/s. When smashing the stalk feed, take a low value to pulverize the grain feed and take a high value. In short, choose the appropriate one according to the requirements in the instruction manual. Hammer line speed to fully utilize the efficiency of the shredder.
Hammer screen gap can not be too large or too small
The hammer sieve gap refers to the gap between the end of the hammer and the sieve, which has a great influence on the working performance of the pulverizer. When the hammer screen gap is large, the feed particles in the feed close to the sieve surface are not easy to contact with the sieve sheet, and the chance of being hit is small, and the friction effect of the sieve sheets on them is also weakened due to the low speed, so the power output is decreased. The finished product becomes thicker. When the gap is large to a certain extent, the feed particles on the sieve surface move too slowly, and even the sieve holes are blocked, so that the productivity is further lowered. When the hammer screen gap is small, the outer ring feed is hit by hammers. The feed speed on the sieve surface is high, and it is difficult to pass through the sieve hole, so that the effect of friction pulverization is increased, and the feed is pulverized too finely. Conducive to the discharge of powder, not only waste power, so that the production of electricity is reduced, and the finished product is also too thin.
Under the premise of meeting the requirements of livestock and poultry breeding, the sieve with a larger mesh diameter should be selected as much as possible.
The effect of the diameter of the mesh on the power output of the pulverizer is very significant, and it also directly affects the fineness of the pulverized feed (the average diameter of the feed granules). Feed fineness M = (0.25 ~ 0.33) d. The larger the diameter of the mesh, the higher the electrical output, but the coarser the pulverized material. In general, when smashing the concentrate, the diameter of the mesh hole is from d = 2 mm, and the productivity can be increased by 20% to 35% for every 1 mm increase. On the contrary, the smaller the mesh diameter, the finer the feed pulverization, but the productivity and power output of the machine are also significantly reduced. Therefore, under the premise of meeting the requirements of livestock and poultry breeding, sieves with larger hole diameters should be used as much as possible.
The amount of feed should match the flow of air circulating through the screen.
The type of the pulverizer is different, and the feeding amount is different, which directly affects the pulverization efficiency. When the feed amount is greater than a certain value of the air flow rate flowing through the sieve hole, the material will be piled up on the sieve surface to cause the sieve hole to have different degrees of blockage. The thickening of the circulation layer in the pulverization increases the resistance acting on the rotor, resulting in pulverization efficiency. decline. Therefore, when the feeding amount is only in accordance with the design requirements of the pulverizer, the power consumption is the smallest, the productivity is the highest, and the motor is not overloaded, and the user can obtain a satisfactory pulverized product.
Pay attention to the balance of the machine
The pulverizer is a high-speed rotating machine that undergoes dynamic and static balance tests at the factory. After a period of use, when the edge of the hammer wears to 1/2 of the width of the hammer, the change or turn must be performed in situ. The axially fed pulverizer is also adjustable for use when the blade of the priming device is worn. When you need to replace the new hammer, you need to re-match the group, and ensure that the quality difference of each group does not exceed 5g, to avoid affecting the balance of the machine and generate vibration and noise.
Pay attention to the tightness of the transmission belt
The pulverizer belt elasticity can be adjusted by the front and rear position of the movable motor on the machine base. To avoid the belt slipping, the loose side can be made up to increase the wrap angle.
Dry Wall Screw is a kind of nail, its name is from the English Drywall Screw direct translation, in the appearance of the biggest feature is the flare head shape, divided into double-line fine tooth dry wall Screw and single-line thick tooth dry wall Screw, the biggest difference between the two is that the thread of the former is double thread.
Product description the name of the dry wall Screw is directly translated from English Drywall Screw, its biggest feature in appearance is the shape of the flare head, divided into double-thread thin-thread dry wall Screw and single-thread thick-thread dry wall Screw, the biggest difference between the two is that the thread of the former is double thread, which is suitable for the connection between plasterboard and Metal Keel whose thickness is not more than 0.8 mm, while the latter is suitable for the connection between plasterboard and Wooden Keel. The Dry Wall screw series is one of the most important categories in the whole fastener product line. This product is mainly used for the installation of various Gypsum Board, light partition wall and ceiling ceiling ceiling. Double-thread fine-tooth phosphating dry-wall screw is the most basic product line, while blue-white Zinc dry-wall screw is a supplement. Slightly different is that black phosphating has a certain degree of lubricity, attack speed (the speed of penetration into a specified thickness of steel plate, is a quality assessment index) slightly better, and blue and white zinc in rust-proof effect slightly better, and the product of light color, not Easy after the paint decoration panchromatic. There is almost no difference in rust resistance between blue-white zinc and yellow zinc, only because of different usage habits or users`preference.
Double-thread fine-pitch dry-wall screws,single-thread heavy-pitch screws,Dry wall screws
Nantong Safe Yawl Import &Export Co.,Ltd , https://www.ntsyspring.com