After the renovation, most of the owners can not help but have more or less regrets. Some of them are errors in the construction of the decoration company, but many of them are regrets caused by their own wrong decisions. So how to avoid these regrets, this site Xiaobian specifically for you to sort out some solutions!
Power socket is not enough
Sorry index: ★★★★★
Case: "My home's power outlet is basically the kind of two-hole and three-hole socket connected to a panel, but many kitchen appliances are three-pin plugs, sometimes with rice cookers can not use the electromagnetic oven, microwave ovens can not At the same time using an electric kettle, it's very troublesome to have a meal!"
Truth: Most homes are installed with conjoined secondary and tertiary outlets, but in fact such installations are not reasonable. Kitchen appliances such as rice cookers, microwave ovens, electric kettles, range hoods, etc. are usually three-pin plugs. If all-in-one outlets are installed, the three-pin outlets in the kitchen will be insufficient. Therefore, when installing a socket, careful consideration should be given to the specific conditions of the electrical appliances in each room, and the sockets should be properly configured.
Hydroelectricity laying is not straight
Sorry index: ★★★★☆
Case: “When our house was renovated, workers said that it would be a waste of material to lay horizontally and vertically. Now that it is out of order, the home circuit has a problem to repair. The master said that the wires had been twisted and twisted, and now the problem of wires is not good enough to overhaul.â€
Truth: Water and electricity should be laid as horizontally and vertically as possible, and it should not be “overwhelmed†like a spider web. Otherwise, it will be difficult to identify the location of the pipes and wires for pre-embedding. It will be very troublesome to repair them. In the later stage, if nails are still to be hit on the wall, it may break through the wires or pipes, resulting in leakage or bursting of the pipes.
Wire maintenance is very troublesome
Sorry index: ★★★★☆
Case: "The socket of the bedroom needs to be replaced. The master removed the socket and found that the three wires of the socket had the same color. The master said that the wire had the same color, no separation was installed, it could not be replaced immediately, and the line type could be detected by removing the line along the way."
Truth: The color separation of the wires is usually red for the live line, blue for the neutral line, and yellow and green lines for the ground line. If you do not separate the wires, it is easy to install the wrong switch. In particular, if the outlet is of any color, it will not be clear when the latter is installed. Which is the neutral line, which is the ground line, and if the connection is wrong, it will trip.
Special electricity is not special line
Sorry index: ★★★☆☆
Case: "We didn't understand the decoration either. The construction master said that using the same wire would be enough. Therefore, our home's wires are all 2.5 square millimeters. Now that we use air-conditioning, we will short circuit from time to time. It's really depressing."
Truth: In general, home decoration is selected to cross-section 2.5 square millimeters of wire, but like air-conditioning, electric water heaters and other high-power appliances, it should be special power line, select the cross-section of 4 square mm of wire, so as not to use A short circuit occurs in these high-power appliances.
Bathroom socket unobstructed
Sorry index: ★★★☆☆
Case: "I haven't paid attention to the waterproof problem of the bathroom socket. The bathroom is still equipped with an ordinary socket. If the socket is splashed by water when it takes a shower, it will be troublesome."
Truth: Because of the high humidity in the bathroom, when installing the socket must pay attention to moisture-proof waterproof, otherwise it will leave a great security risk. The outlet socket installed in the bathroom must be equipped with a splash-proof cover. If an ordinary socket has been installed, attach a splash-proof cover to the outside of the socket to prevent leakage of the inlet water.
Switch socket is blocked
Sorry index: ★★★★☆
Case: "The switch of my living room lighting is installed behind the door. Every time I go home at night, I must close the door to turn on the lights. Evening darkness is easy to trip."
Truth: This kind of decoration regret is also more common, not the door handle switch blocked, is the socket "hide" behind the furniture, this not only adds to the use of the trouble, but also a certain degree of security risks.
In general, if the door is opened to the left, the door switch should be installed on the right side to ensure that the door can be turned on easily. The socket switch is blocked by the furniture, mainly because the furniture is too high or too wide, and eventually the owner has to use the patch panel to solve the problem. Therefore, when installing hydropower, try to set aside enough space for furniture. This can be avoided.
Strong and weak wires are not separated
Sorry index: ★★★★☆
Case: "When installing the circuit, workers said that the separate installation of the wires would increase the cost, and the separation would not have much impact. Who knows that television and telephone signals are often disturbed."
Truth: Power refers to television lines, computer lines, air-conditioning lines, etc.; weak electricity refers to the telephone line, network cable, audio cable, video cable and audio cable. During installation, strong and weak currents must not be worn in the same tube. Install them as far as possible and ensure that the distance between strong and weak currents is at least 20 cm. Otherwise, mutual interference will occur, affecting heat dissipation, and affecting The service life of the wire.
Wire casing is not distinguished
Sorry index: ★★★☆☆
Case: "When friends installed a circuit at home, I saw workers using two types of pipes to wear wires. One was a hard PVC pipe and the other was a hose. It was said that the bearing walls and beams could not be slotted. The hose was used. However, all of my home renovations use PVC pipes."
Truth: Wire sleeves are primarily concerned with the insulation, moisture resistance, corrosion protection and patency of the wires. One of the most common and safest line pipe is PVC pipe. However, PVC pipes cannot be used for positions such as load-bearing walls and beams that cannot be slotted. The use of hoses will not affect the structure of bearing walls and beams.
Improper tap location
Sorry index: ★★☆☆☆
Case: "The faucet in the kitchen, the water column at the outlet is only 10 centimeters from the side of the sink, and when you wash things, you must bow to your body to receive the water.
Truth: It is indeed a troublesome thing to bow to a body or extend an arm to receive washing. In fact, the most suitable faucet outlet is just in the middle of the sink. To avoid the trouble of bending or stretching hands with water in the future, the owner should preferably measure the width of the edge face and the inner diameter of the sink after booking the sink or table, and then select the appropriate length of the faucet.
Decoration experience decoration regret entrance renovation socket switch electrical bathroom furniture decoration find decoration company okay decoration living room bedroom bedroom lamp
Sand Paper discs are versatile grinding and polishing tools that are widely used in industries such as woodworking, metalworking, auto repair, furniture manufacturing, and electronics and electrical appliances. They are designed to quickly and efficiently remove the surface layer of materials, making them smooth and ready for subsequent processing. The following is a detailed introduction to sandpaper disc products:
Product Features
1. Efficient grinding
Sand paper discs use high-quality abrasives to provide excellent cutting ability and durability. Whether it is fast grinding of rough surfaces or fine polishing of smooth surfaces, they can provide perfect grinding results.
2. Multiple material options
A variety of abrasives such as aluminum oxide, silicon carbide, and zirconium corundum can be selected to adapt to different materials and grinding requirements. Aluminum oxide is suitable for most uses, silicon carbide is suitable for hard materials, and zirconium corundum provides longer service life and efficient cutting.
3. Wide range of grit sizes
The grit size ranges from coarse to ultra-fine to meet the needs of different grinding stages. From removing old paint layers to achieving high-gloss surface treatment, sandpaper discs can achieve precise control.
4. Easy to install
Provide two installation methods: Hook & Loop and PSA, which are easy to replace and firmly fix, suitable for various grinding equipment.
5. Customized service
Different sizes, shapes and abrasive types can be customized according to customer needs to meet the needs of special applications.
Application areas
1. Woodworking and furniture industry
Sandpaper discs are suitable for grinding and leveling wood, which can effectively remove surface defects and improve the coating effect.
2. Automobile manufacturing and maintenance
Treat the surface of the car body before painting to ensure that the paint surface is smooth and flawless. It can also be used to repair and polish old paint layers.
3. Metal processing
It is used for surface treatment of metal materials such as stainless steel and aluminum alloy to remove oxide layers and welding marks and achieve high-quality polishing effects.
4. Electronics and electrical appliances
Provide fine grinding solutions, suitable for surface treatment of electronic components and housings.
Sand Paper Disc,Aluminum Oxide Abrasive Discs,5Inch Aluminum Oxide Abrasive Disc,5 Inch 8 Holes Sanding Disc
Foshan Nate Abrasive Science & Technology Co.,Ltd , https://www.nateabrasives.com